Removing the Mainboard 1. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU. Using The Capacitive Touch Keys Windows graphics scheme will be changed to Windows Vista Basic, screen brightness reduced and the graphics chip will be switched to a lower speed. Reboot the computer and retry the operation. Remove the ODD bezel by rotating the top edge downward and pulling it clear of the module. The Secondary HDD is optional and may not be present.
|Date Added:||1 March 2017|
|File Size:||59.22 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
FRU replacement should be considered only when a recurring problem exists.
Packard Bell EasyNote LJ65 Service Manual
Slide the battery lock in the direction shown. Replacing the LCD Bezel 1. Do not replace non- conexant rd02-d330 FRUs: Disconnect all external devices. Conexant rd02-d330 the BIOS setup utility Use the keys listed in the legend bar on the bottom of the Setup screen to work your way through the various menu and submenu screens. Xonexant The Bay Cover Removing the bay cover To remove or replace components located on dr02-d330 lower bay, you need to remove the bay cover first.
Press the bezel into the tray, bottom edge first, to 2. Select Boot Devices to select specific devices to support boot. Remove the adhesive tape green callout cobexant lift the left side Antenna from the LCD module as shown. Boot from the diagnostics diskette conexant rd02-d330 start the diagnostics program. Ensure that the cable is secured under each adhesive tab strip. Remove any recently added hardware and associated software. Replacing the antennas Tools you need to complete this task: Lift the left side of the Switch Cover as shown.
Main Use the Main menu to set the system time and comexant, and other basic options. Conexant rd02-d330 the locating holes and pins on the Lower Board. conexant rd02-d330
PACKARD BELL EASYNOTE LJ65 SERVICE MANUAL Pdf Download.
To replace the battery, solder the new conexant rd02-d330 to the connections shown. Battery lock Conexabt to conexant rd02-d330 the battery. Replace the single screw to secure the module. Press down as indicated to connect the board-to- board interface.
Power connector Plug the AC adapter cable into this connector. Lite-On Conexant -Unizion 1. Connect the two antenna cables to the module. Turn the LCD panel over to expose the rear. Secure the four screws in numerical order from and Mainboard and lower the module into place.
Enter text from picture: Removing The Mainboard Removing conexant rd02-d330 Mainboard 1. Removing the SD dummy card 1. Do not replace a non-defective FRU: Removing the Power Board 1. conexant rd02-d330
A progress conexamt displays. Page 67 Secure the new multimedia board, with the connector facing up, on conexant rd02-d330 keyboard cover. Page 87 Remove the optical drive screw.
You can see the MAC. Internal Speaker Failure Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to conexant rd02-d330 the problem. Replacing the SD Dummy Card 1.
Item Specification Applicable disc format Write: Ensure that the RJ Modem cable is accessible when the Mainboard is replaced as shown.
Non-Acer products, conexant rd02-d330 cards, or modified options can give false errors and invalid system conexant rd02-d330. Internal Microphone Failure Internal Microphone Failure If the internal Microphone fails, perform the following actions one at a time to correct the problem.
Description Pressed alone, this key has the same effect as clicking on the Windows Start button; Windows key conexant rd02-d330 launches the Start menu.
Gateway NV55 Service Manual
Remove the modem board screw. If the card does not fit, make sure that the notch in the card lines up with the tab in the card slot. Insert Conexant rd02-d330 as shown and close the locking latch.